How To Clean A Motorbike Helmet? Cleaning your helmet is something that we all think we can do, but do you actually know how to do it correctly? Think again if you’re smugly nodding your head and attempting to reach for the furniture polish as well as an old rag. We’ll show you everything you have to know to keep the most essential component of your riding gear in good condition this summer.
Before we begin with How To Clean A Motorbike Helmet, you will require:
- A used toothbrush
- A gentle nailbrush
- A few cotton buds
- Four anti-lint cloths
- A sponge that is not abrasive
- Cleaning supplies
How To Clean A Motorbike Helmet?
By following the steps of How To Clean A Motorbike Helmet below, you can resolve the safety, bacteria, and general odor issues in under ten minutes. Because it is exposed to the elements, the exterior of your helmet should be cleaned more frequently. Liners should be washed and removed on a quarterly basis, depending on the circumstances.
Step 1: Preparation
First and foremost. Wash your hands and make certain that all of your clothes are clean; the last thing you would like to do is harm the paintwork on your helmet since a piece of dirt was hidden in one of your clothes. Put your tools on a clean work surface, preferably the kitchen side. Take pictures of the outside and inside of your helmet if necessary; these will come in handy when you’re trying to put it back together.
Step 2: Removing
Remove your helmet. We used an Arai helmet for this feature, however, the same rules should apply to any helmet. Remove anything you know you can remove with care; if in doubt, consult the manual which came with your helmet. If, like 99.9% of bikers, you threw it away, call the helmet manufacturer, request for the technical department, and find out what you must do to strip it down. Don’t be too harsh; if something feels like it’s about to snap, it possibly is.
Step 3: Only the essentials
If you are confident in your ability to unscrew as well as remove base plates, etc., go ahead and do so. Lay out what you’ve taken out in the order you’ll need to replace it. Don’t get carried away but also strip everything away; only take what you need.
Step 4: Getting Wet
Most helmets have removable cheek pads, and some have completely removable linings. Soak them in water with a small portion of PH-neutral baby shampoo after removing them. Rinse after thoroughly massaging all of the parts. The black slime that emerges will astound you. Place a towel in the bottom of the bath or sink, then place your helmet on it and shower it with warm water.
Soak the helmet, then apply a small amount of shampoo to it and massage it in. At least five times, thoroughly rinse with cold water. Place the helmet as well as any wet parts ahead of a cool fan for 30 minutes. Avoid using the hairdryer or even the airing cupboard.
Step 5: Visor
Use a non-abrasive cloth to clean your visor. Soak it in warm water as well as rub it with a mild soap solution. If possible, remove the dirt with your fingers to avoid damaging the surface of your visor. Enable the visor to dry naturally while standing up. If your visor has an anti-fog coating, take care of it. Reapply any anti-fog coating carefully after it has dried.
Step 6: Cleaning
Use a non-abrasive cloth and a mild soap solution to clean the shell of your helmet. Avoid using petroleum-based cleaning products because they will shorten the life of your helmet. Once more, utilize warm water and avoid being too heavy-handed. If necessary, insert cotton buds into the vents.
Repeat the steps two to three times with the nailbrush or toothbrush in the difficult-to-reach places. Use touch-up pens developed for cars to conceal small stone chips. This will not remove the chip completely, but it will conceal it and prevent water ingress, which will deteriorate the quality of your helmet over time.
Step 7: Applying lubricant
Lubricate the necessary components of your visor mechanism with silicon grease, making sure to wipe away any excess to avoid further damage to your helmet. You should also lubricate the seal all around the visor aperture. Apply sparingly, wiping away any excess. You might like to read: How To Choose Motorbike Helmet
Step 8: Putting everything back together
Put your helmet back together. Take your time repositioning your visor. Most helmet baseplates are adjustable; treat it just like suspension. Try small steps at a time till you get it right. Clean as well as replace side pods/covers. Check that they are all correctly reconnected to the shell; if there are any screws left over, you have done something incorrectly.
Step 9: Polishing
When rebuilt, polish literally the entire helmet with an appropriate polish, and do the visor as well. On the helmet, a mild abrasive is acceptable. Apply it thickly, allow it to dry, and then buff. In the rain, a nice layer of polish on the shell and also the visor will help water bead and roll off easier.
Conclusion
So, here is all about How To Clean A Motorbike Helmet. You can keep your helmet looking new for so many years if you take care of both the interior and exterior. We don’t want to ride around in a shabby-looking helmet, and we’re pretty sure no one wants to put their head in a helmet that smells like old socks. Today is the day to clean your helmet.
