Motorcycles are quite a popular means of transportation in many countries, making traveling and participating in traffic easier. However, for those who have never used a motorbike, this is quite surprising. Follow along with the article 5 Tips About How To Ride A Motorcycle to understand the basic steps of riding a motorbike.
How to Ride a Digital Motorcycle for Beginners
Digital motorbikes are very popular because they have many models and come from many different brands. For those who are new to driving a digital motorbikes for the first time, there will certainly be many surprises. You can ask an experienced person behind the wheel to guide you, but you can also refer to 5 Tips About How To Ride A Motorcycle with the following steps:
Step 1: Sit on the motorbikes and relax your feet on the ground. Or you can lean to one side and prop up one leg for balance.
Step 2: Put the key in the lock and turn to unlock the motorbikes. At this time, the motorbikes will be in N gear (green light).
Step 3: Lift the anti-tilt leg. Then, at the same time apply the brake or press the foot brake. Press the button to start the motorbikes, you can use the handbrake or the foot brake, but the start button must be pressed while holding the brake.
Step 4: Proceed to the gear, release the brake slowly and increase the throttle slowly so that the motorbikes starts moving. Never pull the throttle and release the brake immediately.
Step 5: When the motorbikes has started to move, you gently pull the throttle to shift to larger gears. Always keep the foot brake or handbrake in the ready position.
Note that in the process of moving the motorbikes, always keep the throttle steady, do not increase or decrease the throttle suddenly.
One of the rules you need to remember when riding a motorbike is: If you need to go stably, choose a large gear, and if you need to pull fast and strong, choose a small gear. Specifically, number 1 and number 2 have the effect of pulling the motorbikes forward very quickly and strongly.
You will use this number when stopping at a red light or starting to accelerate forward. Or when you run up the bridge, up the slope, drive from the basement parking. At the beginning of the more stable phase, you will see the motorbikes have a louder or slightly jerky sound. Now you need to increase the gear to 3rd or 4th gear. Then the motorbikes will run more stable and be ready to move on long distances.
For those who are new to first gear, it can be confusing when entering 1st gear the motorbikes is jerky. Therefore, when turning on the key, you can switch from N to 4 so that when starting the motorbikes, it does not pick up, causing a loss of composure.
How to Ride a Scooter for Beginners
It is easier to ride a scooter than a manual motorbikes because this motorbikes uses an automatic transmission. You will not have to go into gear or downshift like a motorbike. Newbies who ride a scooter for the first time should apply the following actions:
Step 1: Get on the bike and relax your feet on the ground. Or you can lean to one side, leaning on one leg for balance.
Step 2: Put the key in the lock and turn to open the motorbikes. For new motorbikes using smart locks, you press the remote. Then turn the motorbikes lock in the correct direction noted on the motorbikes to unlock.
Step 3: Wait for the Fi signal light on the watch to turn off, and push the tilting to stand up. Then, at the same time squeeze the brake and press the start button. You can squeeze one or both brakes, but the start button must be pressed while holding the brake.
Step 4: Release the brake slowly, increase the throttle gently at the same time to let the motorbikes accelerate slowly. Be careful not to forcefully pull the throttle and release the brake immediately.
Step 5: When the motorbikes is running, you adjust the speed by combining the throttle (right hand) and brake (left hand). Gently pull the throttle to accelerate and release the throttle slowly to slow down. After the motorbikes has slowed down, apply the brake to come to a complete stop. Do not brake sharply, pull on the accelerator or release the throttle too quickly. This is also the next information in 5 Tips About How To Ride A Motorcycle.
How to Ride a Motorcycle for Beginners
Riding a hand-held motorbike is more difficult than the two models above. Even those who have mastered manual transmission motorbikes or scooters are still confused. The way to ride a hand-held motorbike requires the driver to move both hands and feet so that they are flexible and fit together. Here are a few notes for beginners to practice clutches:
– Practice out the clutch: For those who are just starting to learn to ride a clutch. You should choose a spacious area with little traffic to ensure safety. First, in gear 1, the left-hand start to release the clutch and does not pull the throttle. Release slowly until the vehicle begins to roll slowly. When proficient, the driver will know where to release the clutch when the vehicle moves. From there, adjust the throttle accordingly.
If you release the clutch too quickly, the motorbikes will die, if you don’t release the clutch enough, the motorbikes will not run. It will drift downhill if you don’t brake.
– Go with the right gear: When driving a manual scooter, you need to shift to the right gear for the speed of the motorbikes running. Because of slow speed, high gear can stall. At slow speed, shift to low gear, when you need to increase speed, shift to high gear. You can also tell if you’re going in the wrong gear by listening to the motorbikes. If there is a squealing sound and the motorbikes jerks. That is, you are going to a higher gear than the rolling speed.
– Do not cut the clutch to drop the slope: When cutting the clutch to drop the slope, the motorbikes can drive faster because there is no longer an engine brake. However, it causes the motorbikes to lose traction, reducing the effect of the brakes. Dangerous if the road is winding, many bends. You only use the clutch to shift gears and control the clutch when running low gear, slow speed. Cutting the clutch to drop the slope can be dangerous for vehicle drivers at any time.
– Rule 1 – 0 – 2: The rule of a hook gearbox when driving a manual scooter is to step on 1. Hook up to 2 but there is a mezzanine of 0. When at 1, hook half of the gear lever to return to 0, and the strong hook will go up 2. Otherwise when at 2, pedal to half the force will go down 0, step down hard 1. This is also the next information in 5 Tips About How To Ride A Motorcycle.
– Starting and stopping motorcycles at N: When starting the motorbikes, always stay in N and then go to 1. Do not stay in 1, or 2 and start the engine. Because if you lose control of the clutch, the throttle can cause you to panic. Return to N, start the engine, make sure everything is ready, then enter 1 to depart.
Some people, when driving a clutch motorbikes to the place, stop the motorbikes often to 1, even 2, 3. Then release the clutch for the motorbikes to turn off the engine or turn the key to turn off the engine. This way of driving is dangerous because if another person is not proficient in climbing into the motorbikes, it will be difficult to control the situation if not paying attention. Therefore, please return to N before turning off the engine to ensure safety next time.
Some Skills Needed For First-Time Motorcycle Learners
Riding a motorbike at the right speed:
Mastering speed makes it easier for you to handle situations that may occur on the road. At the same time do not violate traffic laws. You should only accelerate when you feel that there is enough space in front of you to brake if there is an unexpected situation. This is also the next information in 5 Tips About How To Ride A Motorcycle.
Go with the correct vehicle number:
If traveling on a mountain road with many steep passes, use a low gear and remember the principle of “upshift, downshift”. Because when going uphill, a low gear will help transmit large torque. And when going downhill, the low gear will hold the motorbikes not following inertia, called engine braking. With flat roads, and few vehicles, you use a higher number of vehicles to make the engine operate stably, the motorbikes moves at a steady speed, without jerks.
Wide view:
Wide vision is always essential when you’re on the road. Especially when traveling on small, narrow roads, with many cuts in residential areas. When you have a wide view, you will be ready to brake at any time by placing 1 or 2 fingers on the brake handle as a reaction fulcrum.
Be aware of road signs:
When moving the motorbikes on the road, you need to be in a state of intense concentration. Always observe and listen to traffic signs such as turn signals, signal lights, and horns… to react promptly to any situation on the road.
Overtaking another vehicle when it is safe to:
In many cases, you should pass large vehicles such as trucks and containers when there is enough space and time to actively throttle. Otherwise, it is very easy to be passive in unexpected situations such as the motorbikes in front of you braking sharply, and turning to the sides.
However, you need to pay special attention to only passing the vehicle when it is safe to observe, even on the opposite side of the lane. Need to turn signal – turn left to ask for directions, accompanied by a signal horn, and slowly increase the throttle. This is also the next information in 5 Tips About How To Ride A Motorcycle.
Hopefully the article 5 Tips About How To Ride A Motorcycle will provide useful information for you.
Thanks for reading!
